XinaBox xCHIP Temperature Sensor
- RS stock no.:
- 174-3747
- Mfr. Part No.:
- SW10
- Manufacturer:
- XinaBox
Discontinued product
- RS stock no.:
- 174-3747
- Mfr. Part No.:
- SW10
- Manufacturer:
- XinaBox
Technical data sheets
Legislation and Compliance
- COO (Country of Origin):
- CN
Product Details
xChip Boards
xChips are a rapid electronics development ecosystem to help reduce development time and simplify making custom products as well as aiding learning. Without soldering, wiring, breadboarding, or hardware knowledge you can assemble a circuit in minutes, and concentrate on coding.
xChips are compatible with the platform you want to use and bridges are available for the most popular pltatforms; Raspberry Pi, Minnowboard, Beaglebone, Micro:bit, Pixhawk and 96 boards. Rather than bridging to Ardunio, we offer compatible cores for Arduino Uno, the CC01, and for Arduino Zero, the CC03.
xChips utilise I2C, and due to this bus architecture, unlimited expansion of circuits is possible. Limitations of I2C addresses have been negated by development multiplexers.
Because of its simple connection method, it is easy to build quickly - for prototyping and small product runs
xChips connect to each other using an xBus connector, available from RS 174-4977.
Some xChips need an xPDI connector (RS 174-4974) to connect to programming interfaces, such as the IP02 or IP03.
xChips are compatible with the platform you want to use and bridges are available for the most popular pltatforms; Raspberry Pi, Minnowboard, Beaglebone, Micro:bit, Pixhawk and 96 boards. Rather than bridging to Ardunio, we offer compatible cores for Arduino Uno, the CC01, and for Arduino Zero, the CC03.
xChips utilise I2C, and due to this bus architecture, unlimited expansion of circuits is possible. Limitations of I2C addresses have been negated by development multiplexers.
Because of its simple connection method, it is easy to build quickly - for prototyping and small product runs
xChips connect to each other using an xBus connector, available from RS 174-4977.
Some xChips need an xPDI connector (RS 174-4974) to connect to programming interfaces, such as the IP02 or IP03.
This XCHIP is a temperature-to-digital converter using an on-chip band gap temperature sensor and Sigma-Delta A-to-D conversion technique with an overtemperature detection output.
Product Highlights
I²C-bus interface with up to 8 devices on the same bus
Temperature range from -55°C to +125°C
Frequency range 20 Hz to 400 kHz with bus fault time-out
Applications
System thermal management
Personal computers
Electronics equipment
Industrial controllers
Specifications
I²C-bus interace with up to 8 devices on the same bus
Temperature range from -55°C to +125°C
Frequency range 20 Hz to 400 kHz with bus fault time-out to prevent hanging up the bus
Programmable temperature threshold and hysteresis set points
Supply current of 1.0 μA in shutdown mode for power conservation
Stand-alone operation as thermostat at power-up
I²C-bus interface with up to 8 devices on the same bus
Temperature range from -55°C to +125°C
Frequency range 20 Hz to 400 kHz with bus fault time-out
Applications
System thermal management
Personal computers
Electronics equipment
Industrial controllers
Specifications
I²C-bus interace with up to 8 devices on the same bus
Temperature range from -55°C to +125°C
Frequency range 20 Hz to 400 kHz with bus fault time-out to prevent hanging up the bus
Programmable temperature threshold and hysteresis set points
Supply current of 1.0 μA in shutdown mode for power conservation
Stand-alone operation as thermostat at power-up
Xinabox Modular Prototyping Boards
Specification
Attribute | Value |
|---|---|
| Kit Name | xCHIP Temperature Sensor |